Block Wall Calculator

Concrete blocks, mortar and grout for 8x8x16 CMU walls. Enter wall size: get block count, mortar bags and grout fill.



Estimates only. Standard 8x8x16 in blocks with 3/8 in joints: 112.5 blocks per 100 sq ft. Material estimate only, not structural design.



How many blocks do you need for a block wall?

A 20 by 4 ft wall needs 90 blocks net, about 7 mortar bags (80 lb), and 28.9 ft3 of grout if every cell is filled. Use this block wall calculator for any wall size: enter the length and height and it works out the block count with a waste allowance, the number of 80 lb mortar bags, and the grout volume in cubic yards (plus the equivalent number of 80 lb concrete bags). The maths is based on standard 8x8x16 in CMU with 3/8 in mortar joints, which gives 112.5 blocks per 100 square feet.

How to use this calculator

  1. Enter the wall length and height. You can type in feet, inches, metres or centimetres; the calculator converts for you.
  2. Choose a waste margin. Ten percent is a safe default for garden and freestanding walls; use five percent for simple straight runs with few cuts.
  3. Choose how many cells to grout: every cell, every 2nd cell, every 3rd cell, or no grout. Real walls usually only grout the reinforced cells.
  4. Read the results: block count, mortar bags, and grout in cubic yards, with the working shown step by step.

The formula

Each standard 8x8x16 in block, with its 3/8 in mortar joint, occupies 8 by 16 in of wall face. That is 128 square inches, or 8/9 of a square foot. One divided by 8/9 gives 1.125, so:

Blocks = wall area (ft2) x 1.125

Add 5 to 10 percent for cutting and breakage. Quikrete states that each 80 lb bag lays up to 13 standard 8x8x16 blocks. Treat that as the best case and keep the waste margin. Grout is about 0.321 ft3 per block when the cell is fully filled, per NCMA guidance of 36.1 ft3 per 100 square feet. The calculator rounds every result up, so you never order a fraction of a bag.

Practical tips

  • Order 5 to 10 percent extra. Cuts around corners, openings and steps are where waste comes from, and blocks do break in transit.
  • On a real wall, grout only the cells the design calls for, usually reinforced cells and cells around openings. Most garden walls are not fully grouted.
  • Keep courses level and plumb as you go. A 4 ft level is enough for garden walls; check every second course.
  • Check your supplier’s block dimensions before ordering. This estimate assumes true 8x8x16 in units with 3/8 in joints.
  • Material estimate only, not structural design. Retaining walls, walls that carry loads, and any wall needing lintels or reinforcement design should be checked by a qualified professional before you build.

Block wall FAQs

How many blocks do I need per square foot of wall?

1.125 blocks per square foot for standard 8x8x16 in CMU with 3/8 in mortar joints. That is 112.5 blocks per 100 square feet, before waste. Add 5 to 10 percent for cutting and breakage.

How many mortar bags do I need for a block wall?

Roughly one 80 lb bag of mortar per 13 blocks. A wall of 90 blocks needs about 7 bags net; with 10 percent waste (99 blocks) you need 8 bags.

How much grout does a block wall need?

About 0.321 ft3 of grout per filled cell, so 100 square feet of fully grouted wall takes about 36.1 ft3 (1.34 cubic yards). Use the calculator to pick how many cells you will fill: every cell, every 2nd, every 3rd, or none.

More in the concrete calculator hub, including mortar and poured walls.

Sources

Scroll to Top