Self-Levelling Concrete Guide: Prep, Priming, Pouring and Curing

Worker pouring smooth grey self-levelling concrete compound onto an indoor floor and spreading it with a gauge rake.

Self levelling concrete, also spelled self leveling concrete in the US, is a pourable cement based mix that flows out and finds its own level. It flattens dips and bumps in a floor before tile, vinyl, wood or carpet goes down. Used well, it saves hours of grinding and patching. Used badly, it cracks, peels or leaves ridges that show through the finished floor.

Direct answer: Check the floor is a candidate first, repair cracks and clean the slab, prime with the maker primer, seal gaps and doorways, mix each bag to the exact water ratio, pour in a continuous ribbon, spread with a gauge rake, roll with a spiked roller, and leave it alone to level. Most bagged products pour at 1/8 inch to about 1 1/2 inches per lift, walkable in 2 to 4 hours, with flooring after the time on the bag. Do not use it as a structural repair, on a settling slab, or on a floor that must slope to a drain.

Underlayment, topping or deep fill: pick the right product

Not all self levelling products do the same job. An underlayment flattens a floor before a covering goes on top. It is not designed as a finished floor. A topping, sometimes called a wear layer, is rated to be the finished floor or to take a coating. A deep fill product handles greater depth in one lift, while a standard product handles thin smoothing.

Check depth range before you buy. US guides cite most products at 1/8 inch to about 1 1/2 inches. UK guides cite standard compounds at 2 mm to 10 mm, and deep fill to 50 mm. Pouring too thick traps moisture and cracks. Pouring too thin stops flow. If dips exceed the range, fill the bulk with screed first.

Also check substrate limits. Fibre reinforced products suit timber floors, with a flexible primer. Some products cannot be used over gypsum floors or damp slabs. Read the bag.

Product typeTypical depth per liftBest forLimit
Standard underlayment2 mm to 10 mm, or 1/8 inch to 1 inchMinor smoothing before flooringNot a finished floor
Deep fillUp to 50 mm in UK guidesDeeper undulationsHigher bag count, check cure time
ToppingAs rated on data sheetFinished floor or coated floorMust be rated as a topping
Fibre reinforced3 mm to 40 mm, product dependentTimber and flexing floorsDo not use a spiked roller on some types

Is your floor a candidate?

Map the floor first with a long level or laser level. Mark high spots and dips, and measure the deepest dip. If the floor slopes by design to a drain, do not use leveller there.

Check the slab underneath. Repair structural cracks before you pour, as leveller will crack where the slab cracks. Do not pour over a settling slab. Check for damp and efflorescence, and test moisture as the maker directs, especially before vinyl or wood.

Check what is on the floor now. Old adhesive, paint, sealer, oil and grease all block bond. Sweeping rarely removes them. Grinding or shot blasting is often needed to open the surface.

Preparation: clean, prime, seal gaps

Clean thoroughly, then profile where needed. Vacuum dust after grinding. Fill cracks and holes, and let the repair cure.

Prime with the maker primer, not a substitute. Primer seals porous concrete so it cannot pull water out too fast, which causes dusting and pinholes. On smooth surfaces, a grip primer gives bond. UK guidance warns against PVA, which can re-emulsify and cause delamination. Let primer dry as the label directs.

Seal every gap before you pour. Leveller flows like water into vents, drains and the next room. Use foam strip or caulk at wall gaps and pipes, and a timber dam at doorways.

Mixing: exact water, lump free, fast

Measure water first, then add powder while mixing. Never guess water. One product takes 7 quarts per 55 lb bag, another 5.25 to 5.75 quarts per 50 lb bag. Extra water weakens the surface and causes dusting and cracking. Too little water leaves lumps.

Mix with a high torque drill and paddle for 2 to 3 minutes, keeping the paddle submerged to limit air. Scrape bucket sides clear. The mix should be lump free, like thick pancake batter. Wear a dust mask when handling powder.

Plan help before you start. Working time is about 10 to 20 minutes for many products, and some rapid products are near 10 minutes. One person mixing while another pours keeps a wet edge.

Pouring and spreading step by step

Start farthest from the exit, and pour in a continuous ribbon into low areas first. Spread with a gauge rake set to target depth. Pass a spiked roller over the wet surface to release air, unless the maker says not to for fibre products.

Keep a wet edge. Each new batch must flow into the previous batch while still wet. Do not overwork the surface once it has levelled. Do not spread it thinner than the minimum depth, as thin edges curl and break away.

Protect the pour while it cures. Keep drafts, direct sun and forced heat off it, as fast drying causes cracking. Keep traffic off until the bag time, commonly 2 to 4 hours. Wait the full flooring time, often about 16 hours, and check moisture before wood or vinyl. See how to cure concrete and how long concrete takes to cure.

How many bags do you need?

Estimate from area and average depth, then add waste. Coverage is given for a stated depth. A 20 kg deep fill bag covering only 0.5 square metres at 20 mm shows how fast deep work consumes bags. Measure dips, do not guess.

Work out bags like this. Multiply area by average depth, convert to bag coverage on your product, then add about 10 percent for waste. Buy bags from the same product, and mix a little more than you need. Running short mid pour is worse than one spare bag.

If the bag count looks very high, reconsider. Deep dips may be cheaper to fill with screed first, then level thinly on top.

FaultLikely causeFix or prevention
PinholesUnprimed porous slab, air in mixPrime fully, mix with paddle submerged
CrackingToo much water, too thin, slab crack belowExact water, minimum depth, repair slab first
DelaminationWrong primer, dirty or sealed surfaceGrind, clean, use maker primer
Ridges at jointsSecond batch onto set edgeKeep wet edge, work in pairs
Dusty surfaceExtra water, fast drying, draftExact water, protect from draft and sun

Frequently asked questions

Do I really need primer?

Yes, in almost every case. Primer controls water loss into porous concrete and gives bond on smooth surfaces. Skipping it is the most common cause of failed levelling work.

Can I use PVA as a primer?

No. UK trade guidance warns that PVA can re-emulsify under wet compound and cause the layer to lift in sheets. Use the maker primer or an SBR primer as directed.

How thick can I pour self levelling concrete?

Follow your product data sheet. Many standard products pour at 1/8 inch to about 1 1/2 inches, or 2 mm to 10 mm in UK terms. Deep fill products go deeper, but never exceed the rated maximum in one lift.

Can I pour it over tiles or wood?

Over tiles, only with a suitable grip primer and a product rated for that substrate. Over wood, use a fibre reinforced product and a flexible timber primer, and check movement and deflection first.

When can I lay flooring on top?

After the time on the bag, and after moisture checks where required. Some products allow flooring after about 16 hours, others need longer. Do not rush wood or vinyl over a damp layer.

Can I use self leveller outdoors?

Most underlayments are for interiors. Outdoor use needs a product rated for exterior exposure, freeze and thaw, and drainage. A floor that must slope to a drain should not be levelled flat.

Conclusion

Self levelling concrete rewards preparation and punishes shortcuts. Choose the right product for depth and substrate, repair and clean the slab, prime correctly, seal gaps, mix to exact water and pour with a wet edge. Protect it while it cures, and check moisture before flooring. Do that, and you get a flat, stable base that your finished floor deserves.

Sources

About the author

Kaleemullah Formulas use standard geometry and published bag yields; sources are linked in each article.

Leave a Comment

Your email address will not be published. Required fields are marked *

Scroll to Top