Fixing a shelf, a gate post, a handrail or a heavy cabinet to concrete is not like fixing to timber. Concrete is hard and brittle. A wood screw will not grip it, and a nail will bend or crack the surface. You need the right anchor for the load and the base material, and you need a clean, well sized hole. This guide shows how to choose and fit concrete anchors, from light concrete screws to heavy wedge and chemical anchors.
The direct answer
To anchor into concrete, drill a hole with a carbide masonry bit in a hammer drill, clean out the dust, then fit the anchor the maker states for your load. Use concrete screws for light to medium loads, sleeve anchors for medium loads in concrete and solid masonry, wedge anchors for heavy loads in solid concrete, and chemical anchors for heavy loads, close edge work and cracked concrete. Never use a heavy expansion anchor close to an edge in weak or cracked concrete.
Start with the base material, not the fixing
The same anchor can work well in solid concrete and fail in hollow block. In hollow block, an expansion anchor may expand into a void and spin. In soft brick, expansion can crack the brick. Drill a test hole in a hidden spot if you are unsure.
Load direction matters too. Tension pulls the anchor out, while shear slides it across the surface. Many fixings are stronger in shear than in tension. A heavy gate or an overhead fixing needs more care than a light shelf.
Choose the right anchor
| Anchor type | Best for | Avoid in |
|---|---|---|
| Concrete screw | Light to medium loads, timber plates, brackets | Heavy structural loads, very soft masonry |
| Sleeve anchor | Medium loads, concrete and solid masonry | Hollow block, close edge work |
| Wedge anchor | Heavy loads in solid concrete | Hollow block, brick, close edges |
| Drop in anchor | Flush fixings, overhead bolts, threaded rod | Hollow block, shallow slabs |
| Chemical anchor | Heavy loads, edges, cracked concrete | Rush jobs, wet holes unless rated |
| Hammer set anchor | Light fixings, conduit, furring strips | Heavy or overhead loads |
Concrete screws are the easiest start for home jobs. They cut their own thread, so no sleeve is needed. Sleeve anchors spread load along a longer sleeve. Wedge anchors give high pull out strength but create strong expansion force. Chemical anchors use resin, create no expansion force, and suit edge work, but need cure time.
Spacing and edge distance
Anchors placed too close together or too close to an edge can crack concrete or pull out as a group. A widely quoted rule for mechanical anchors is at least six times the anchor diameter for spacing and edge distance. Always follow the maker data sheet, because rated values vary by concrete strength and embedment.
| Anchor diameter | Guide spacing | Guide edge distance |
|---|---|---|
| 6 mm | 36 mm | 36 mm |
| 8 mm | 48 mm | 48 mm |
| 10 mm | 60 mm | 60 mm |
| 12 mm | 72 mm | 72 mm |
These figures use the six times diameter guide only. They do not replace maker load tables. For structural fixings, get the load checked.
Tools you need
- Hammer drill or rotary hammer, with a carbide masonry bit matched to the anchor.
- Tape measure, pencil, spirit level and masking tape for depth marking.
- Vacuum, blow out pump or brush for cleaning holes.
- Safety glasses, dust mask, gloves and hearing protection.
- Socket set or driver bit to suit the anchor head.
- Torque wrench for heavy anchors where the maker states a torque value.
For drilling technique in more depth, see our guide to drilling into concrete.
Step by step: fit a concrete screw
1. Mark and check
Mark the fixing points. Check for pipes and cables with a detector where one may be present. Avoid joints, cracks and edges. Keep at least the guide edge distance in the table above, and more for heavy loads.
2. Drill the hole
Fit the bit size the screw maker states. Mark the depth on the bit with tape. Drill the hole about 6 mm deeper than the screw will go, so dust has somewhere to sit. Hold the drill square to the surface. Let the hammer action do the work. Pushing hard only wears the bit and heats the hole.
3. Clean the hole
Blow or vacuum dust out of the hole. Dust stops a screw cutting a full thread and stops resin bonding in a chemical anchor. Brush the hole, then blow it again for chemical fixings. Repeat until no loose dust comes out.
4. Drive the screw
Place the fixture over the hole. Drive the screw with a driver on a firm setting, but stop when it is snug. Overdriving strips the thread in the concrete. If the screw spins, stop. Do not keep driving it in hope. Move to a new hole a short distance away, or enlarge the hole and fit a plastic anchor as a rescue fix for a light load.
Step by step: fit a wedge or sleeve anchor
Drill and clean the hole as above. For a wedge anchor, tap it through the fixture until the washer sits flat, then tighten the nut to maker torque. For a sleeve anchor, insert it through the fixture, then tighten so the sleeve expands. Do not hammer a wedge anchor after tightening.
Step by step: fit a chemical anchor
Drill to maker diameter and depth. Clean fully, brush and blow at least twice. Inject resin from the back forward, filling about two thirds of the hole. Push the stud in with a slow twist. Hold it square until the resin gels, and do not load until full cure time has passed.
Common mistakes
- Using the wrong bit size, so the screw cannot cut a thread or the sleeve cannot expand.
- Leaving dust in the hole, which weakens every anchor type.
- Drilling too shallow, so the anchor bottoms out before it is tight.
- Placing a heavy expansion anchor close to an edge or a crack.
- Loading a chemical anchor before it has cured.
- Overdriving a concrete screw until it spins freely.
If a screw spins, a plastic anchor in an enlarged hole can save a light fixing. For a heavy fixing, drill a fresh hole in sound concrete instead. A rescue fix is not a structural fix. For other common errors, see our DIY concrete mistakes guide and our rebar versus wire mesh guide before you drill near reinforcement.
Safety notes
Wear eye protection for every hole. Concrete chips fly, and a bit can snap if it hits steel. Stop if you hit reinforcement, and move the hole if you can. Do not drill into a post tensioned slab or a structural beam without professional advice. Overhead fixings need anchors rated for that use.
Frequently asked questions
What is the strongest anchor for concrete?
For heavy loads in solid concrete, wedge anchors and chemical anchors are both strong choices. Chemical anchors often suit edge work and cracked concrete, while wedge anchors suit fast, heavy fixings in sound solid concrete.
Can I use concrete screws in brick?
Yes, in solid brick and block for light to medium loads, if you use the maker bit size and a suitable embedment. In hollow block, a screw may not grip, so use a sleeve or a fixing made for hollow masonry.
How deep should a concrete anchor go?
Follow the maker embedment for your anchor size. As a guide, a concrete screw should go at least 25 mm into solid concrete beyond the fixture thickness, and the hole should be about 6 mm deeper than the screw.
Why does my concrete screw spin?
The thread has stripped, the hole is too large, or the base is soft. Stop driving, fit a plastic anchor in an enlarged hole for a light load, or drill a fresh hole for a heavy load.
Can I remove a wedge anchor?
You can often remove the nut and fixture, but the stud and clip usually stay in the concrete. Cut it flush or grind it flat if it must be removed, and fill the hole if needed.
How long must a chemical anchor cure?
It depends on the resin and the temperature. Some cure in an hour in warm weather, while epoxy types may need 24 hours or more. Read the cartridge label and do not load early.
Conclusion
Good concrete fixings start with the base material and the load, not with the packet on the shelf. Match the anchor to solid concrete or masonry, keep spacing and edge distance safe, drill and clean the hole well, and follow the maker torque or cure time. Do that, and a fixing that looks simple will hold safely for years.
Sources
- Family Handyman: Drilling Concrete and Installing Fasteners
- AIMS Industrial: Concrete Anchor Guide
- Engineer Fix: Types of Heavy Duty Anchors
- BuildToolHQ: Concrete Anchor Spacing and Edge Distance
About the author
Kaleemullah Formulas use standard geometry and published bag yields; sources are linked in each article.