How Much Does a Cubic Yard of Concrete Weigh in Pounds?

Close-up of a ready-mix concrete truck drum and chute pouring wet concrete on a building site


A cubic yard of fresh normal-weight concrete weighs about 4,000 lb. The math is simple. One cubic yard holds 27 cubic feet, and standard concrete weighs roughly 145 lb per cubic foot, which multiplies out to 3,915 lb per yard. Round it, and 4,000 lb is the working figure every contractor uses for ordering, transport, and formwork design. To work out the weight for your own project dimensions, try our concrete weight calculator.

But search online and you will find numbers all over the place: 3,800 lb here, 4,500 lb there, with nobody explaining why the figures differ. The difference is not a mistake. Weight moves with the mix. Dry cured concrete weighs less than fresh concrete, and lightweight mixes weigh far less than standard ones. Below is the unified table other pages are missing, with wet and dry numbers side by side so you can see where the spread comes from.

The Short Answer: About 4,000 lb Wet

Normal-weight ready-mix concrete straight from the truck weighs approximately 145 lb per cubic foot. Multiply 145 by 27 cubic feet in a yard and you get 3,915 lb, which contractors round to 4,000 lb. This is the number you should use for anything that touches the fresh pour. Trailer hire, formwork bracing, crane picks, and soil bearing checks all assume this wet weight.

Once concrete cures and sheds its mix water, it weighs a little less, typically 3,600 to 3,800 lb per yard. Engineers use this cured unit weight for design work, while site logistics always plan on the heavier wet number.

Why the Number Moves: Wet vs Dry, Normal-Weight vs Lightweight

Two things move the weight. The first is water. Fresh concrete contains its full batch water, roughly 280 to 340 lb of it per yard. Over days and weeks that water evaporates as the cement hydrates, and the yard ends up a few hundred pounds lighter.

The second factor is aggregate. Standard mixes use normal-weight stone, sand, and gravel, and ACI 318 lists 145 lb per cubic foot as the unit weight for normal-weight concrete. Lightweight mixes swap some or all of that aggregate for expanded shale, clay, slate, or pumice. Those mixes run about 90 to 115 lb per cubic foot, which drops a whole yard to roughly 2,400 to 3,100 lb. Roof decks, high-rise floors, and fire-rated toppings are the classic lightweight applications, and they weigh nearly a third less than a normal mix.

This is where the confusion on other pages starts. One page quotes the 145 lb per cubic foot figure, another quotes a dry weight, a third quotes a lightweight mix, and none of them labels which one it is giving you. Once you know which state and which mix a figure refers to, the spread from 3,800 to 4,500 lb makes sense.

Weight Table by Mix Type

Here is the unified reference table. It covers the three most common situations: normal-weight concrete fresh from the truck, the same concrete cured and dry, and lightweight aggregate concrete. All figures are per cubic yard.

Mix type and state Unit weight (lb/ft³) Weight per cubic yard (lb)
Normal-weight, fresh (wet) 145 3,915 (plan on 4,000)
Normal-weight, cured (dry) 133 to 140 3,600 to 3,800
Lightweight aggregate, fresh 95 to 115 2,600 to 3,100
Lightweight aggregate, cured 90 to 110 2,400 to 2,970
High-strength normal-weight (typical) 145 to 155 3,915 to 4,200

The normal-weight figures are the ones almost every home project uses. The 145 lb per cubic foot value comes from ACI 318 and is the standard engineering reference for normal-weight concrete in the United States. UK readers working in metric can treat it as roughly 2,300 to 2,400 kg per cubic metre.

What a Loaded Mixer Truck Weighs

A standard transit mixer carries 8 to 10 cubic yards. Take the wet weight of about 4,000 lb per yard and the concrete alone in a full load runs 32,000 to 40,000 lb. Add the truck itself, which typically weighs 25,000 to 30,000 lb empty, and a full mixer tips the scales at 55,000 to 70,000 lb.

Load size Concrete weight Total gross weight (approx)
8 yd³ 32,000 lb 57,000 to 62,000 lb
9 yd³ 36,000 lb 61,000 to 66,000 lb
10 yd³ 40,000 lb 65,000 to 70,000 lb

In the US, the federal gross vehicle weight limit on interstate highways is 80,000 lb, so a full mixer sits within the legal envelope. In the UK, the general limit for articulated vehicles is 44 tonnes, but local roads and bridges can impose much lower limits. Check the regulations on your delivery route before ordering.

Bag Equivalents per Yard

Mixing by hand or in a small site mixer changes the question from yards to bags. An 80 lb bag of premixed concrete yields 0.6 cubic feet of finished concrete. A yard is 27 cubic feet, so 27 divided by 0.6 gives 45 bags per yard. A 50 lb bag yields 0.375 cubic feet, which works out to 72 bags per yard. These figures come straight from manufacturer yield data and hold up in practice.

Bag size Yield per bag Bags per cubic yard
80 lb bag 0.6 ft³ 45
60 lb bag 0.45 ft³ 60
50 lb bag 0.375 ft³ 72

Think about what that means in labour. Forty-five 80 lb bags is 3,600 lb of dry mix to move and mix before you have even started placing. For anything above half a yard, ready-mix delivery usually works out cheaper in time and effort. Our guide to how many bags of concrete per cubic yard walks through the full calculation for each common bag size.

Why Weight Matters for Your Project

Weight is not trivia. It shapes real decisions on every pour.

  • Formwork and bracing. Liquid concrete pushes sideways on formwork with a pressure driven by its weight. Underestimating the weight means under-braced forms, and blown forms are the classic DIY disaster.
  • Trailer and towing limits. Hauling bagged concrete home runs into vehicle payload limits fast. A pickup with a 1,800 lb payload can legally carry just 22 of the 45 bags needed for a yard.
  • Cost planning. Weight feeds into transport surcharges, pump hire, and labour estimates. Before you budget, work out your volumes on the concrete calculator so the weight math starts from an accurate yardage.
  • Structural design. Dead load is the constant weight of the structure itself, and concrete is the heaviest common component. Engineers use the cured unit weight for these checks, never the wet figure.

If you are pricing the job as well as planning the logistics, run the numbers through the concrete cost calculator once you know your yardage. Knowing the weight alongside the cost gives you the full picture before the truck rolls in.

FAQs

Does wet concrete weigh more than dry concrete?

Yes. A yard of normal-weight concrete weighs about 3,915 lb fresh and drops to roughly 3,600 to 3,800 lb once cured, because the free mix water evaporates over time. Plan all site logistics on the heavier wet number.

How much does half a yard of concrete weigh?

Half a cubic yard of fresh normal-weight concrete weighs about 2,000 lb. That is roughly 22 eighty-pound bags, which is why even small pours are heavy work and short-load ready-mix minimums exist.

How much does lightweight concrete weigh per yard?

Lightweight aggregate concrete runs about 90 to 115 lb per cubic foot, so a yard weighs roughly 2,400 to 3,100 lb. It is used for roof decks, fire-rated floors, and any structure where cutting dead load matters.

How much does a cubic metre of concrete weigh?

A cubic metre of normal-weight concrete weighs about 2,300 to 2,400 kg, which is the metric equivalent of 145 lb per cubic foot. The same wet versus dry and lightweight adjustments apply.

How much does a full concrete mixer truck weigh?

A full 10-yard mixer weighs roughly 65,000 to 70,000 lb in total, with the concrete itself contributing about 40,000 lb. The US federal limit is 80,000 lb and the UK general limit is 44 tonnes, but local roads and bridges may set lower limits.

How many 80 lb bags equal a cubic yard?

Forty-five 80 lb bags make one cubic yard, because each bag yields 0.6 cubic feet and a yard holds 27 cubic feet. That is 3,600 lb of dry mix before you add water.

Conclusion

A cubic yard of fresh normal-weight concrete weighs about 4,000 lb. The spread you see online, 3,800 to 4,500 lb, is not sloppiness. It is the honest range once you account for wet versus cured concrete and normal-weight versus lightweight mixes. Use 4,000 lb per yard for site planning, formwork, and transport, switch to the cured weight for structural design, and check your local road limits before the mixer arrives. Get the weight right and the rest of the logistics follow.

Last verified: October 2026.

About the author

Kaleemullah Formulas use standard geometry and published bag yields; sources are linked in each article.

Leave a Comment

Your email address will not be published. Required fields are marked *

Scroll to Top