
Fill expansion joints with a foam backer rod set down into the joint, then a flexible sealant tooled slightly below the surface. The backer rod stops the sealant sinking into the gap and bonding to the bottom, which would stop it stretching as the concrete moves. The sealant keeps water, weeds, and grit out. Done properly, the seal flexes with the slab for years.
Old forums rank well for this question, but their advice is thin. They skip the timing rules, never say when a joint should stay open, and UK product guidance is almost nonexistent. This guide closes those gaps.
The Short Answer: Backer Rod + Sealant
Press a foam backer rod into the joint so it sits below the surface, leaving room above for the sealant. Then gun in a flexible sealant, self-levelling polyurethane for driveways, and tool it smooth and slightly below the slab surface. The sealant bonds to the two sides, the backer rod acts as a bond breaker underneath, and the joint keeps flexing with temperature changes.
Sealant alone would sink into the gap, waste product, and fail because it bonds to the bottom. Backer rod alone lets water through. Together they make a weatherproof, flexible seal that handles foot traffic and car wheels.
What Goes in the Joint
You need three things: a backer rod, a sealant, and a cleaning method. Masking tape helps on decorative slabs.
Backer rod
Backer rod is a closed-cell foam cord sold in coils. Choose a diameter slightly larger than the joint width so it wedges in and stays put. Closed-cell foam will not absorb water. The rod sets the sealant depth and stops the sealant sticking to the bottom of the joint, which is what lets the seal stretch.
| Joint width | Backer rod diameter | Sealant depth (approx) |
|---|---|---|
| 10 mm | 12 mm | 5 mm |
| 12 mm | 15 mm | 6 mm |
| 15 mm | 20 mm | 8 mm |
Self-levelling polyurethane sealant
For driveway joints, self-levelling polyurethane is the default choice. It flows flat in horizontal joints, bonds strongly to concrete, and stays flexible across seasons. Choose a colour that suits your slab; grey blends with most concrete.
Silicone options
Silicone sealants also work and suit wet locations because they tolerate damp and cure fast. For traffic-bearing driveways, polyurethane usually wins on durability.
Cleaning supplies
A stiff brush or a pressure washer, a vacuum or blower for loose grit, and a concrete cleaner for the final wipe. Sealant bonds to clean, dry, sound concrete, not to dust, moss, or crumbling joint faces.
Step-by-Step
Work on a dry day with no rain in the forecast for 24 hours.
- Clear the joint. Pull out weeds, moss, and loose debris. Brush or pressure-wash the joint faces, then let them dry fully. Old crumbly filler must come out down to sound material.
- Fit the backer rod. Press the foam rod into the joint with a blunt tool. Set it deep enough that the sealant above it will be roughly half the joint width. Do not stretch the rod as you push it in.
- Prime if required. Some polyurethanes ask for a primer on very porous concrete. Follow the tube instructions. Most residential driveway work skips this step.
- Gun in the sealant. Cut the nozzle to match the joint width, fill from one end in a steady run, and slightly overfill so no voids remain. Work in shade where possible.
- Tool it smooth. Draw a rounded tool or a gloved finger along the joint in one continuous pass. Tool the sealant slightly below the slab surface so car tyres run on concrete, not on sealant.
- Cure untouched. Keep traffic off the joint for the full cure time on the label, often 24 hours. Protect it from rain during that window.
If you are laying out new joints or repairing an old slab, our guide to concrete control joint spacing explains where the joints should go before you fill them.
Timing and Temperature
Seal on a mild, dry day when the concrete has contracted. Concrete expands in heat and shrinks in cold, so sealing when the gap is widest means the sealant gets compressed later rather than torn apart.
Avoid sealing at the peak of a hot afternoon. The joint is at its narrowest, the sealant skins fast, and winter will pull the stressed seal apart. Avoid freezing weather; most sealants state a minimum application temperature. Never seal into a wet joint or ahead of rain.
New slabs keep shrinking for weeks after the pour. Seal too early and the joints open wider than the sealant can handle. Wait at least 28 days on new concrete. Our guide on how to cure concrete covers what has to happen before any joint work begins.
Sand vs Backer Rod Decision
Sand still turns up in old forum advice, but it is the weaker option. A bed of sharp sand lets the sealant soak down into the grains, wastes product, and can hold moisture against the joint faces. Backer rod sets an exact depth, acts as a proper bond breaker, and stays dry because closed-cell foam does not absorb water. Sand is cheaper, but for a joint you want to seal once and forget, backer rod is worth the small extra spend.
UK Product Equivalents
UK builders merchants stock the same two sealant families. You will find both types in the concrete repair aisle of national merchants and DIY sheds. Look for tubes labelled for concrete expansion joints, paving joints, or driveway joints.
| What you need | What to ask for at a UK merchant | Typical use |
|---|---|---|
| Self-levelling polyurethane | Concrete joint sealant, polyurethane based, self-levelling | Driveways, car parks, horizontal joints |
| Silicone sealant | Exterior or paving silicone sealant | Patios, pool surrounds, damp locations |
| Backer rod | Foam backer rod or joint backing rod, closed cell | Setting sealant depth in any joint |
| Primer | Concrete or masonry primer | Very porous or dusty joint faces |
Measure your joint width before you go, because backer rod is sold by diameter and sealant tubes come in standard cartridge sizes. If you are choosing between filler products, our page on concrete expansion joint filler explains how preformed fillers differ from the sealant system described here.
When NOT to Fill a Joint
Some joints should stay open or be treated differently.
- Isolation joints against buildings. The joint between a driveway and a house or garage wall needs a compressible preformed filler that stays in place. Sealing across it can pass movement into the structure.
- Active fault lines or tree-root zones. If a slab is still shifting because of roots or poor subgrade, sealant will tear within a season. Fix the cause first, then seal.
- Drainage joints. Weep joints in retaining situations are meant to pass water. Sealing them traps moisture behind the structure.
- Slabs under warranty. If the slab is new and still within the contractor’s warranty period, report the issue before you touch it. Your own repair can complicate a warranty claim.
- Joints full of oil or grease. Contaminated joint faces will not hold a bond. Sealing over oil guarantees failure.
FAQs
What is the best thing to fill concrete expansion joints with?
A foam backer rod with a self-levelling polyurethane sealant on top is the standard answer for driveways. The rod sets the depth and acts as a bond breaker, and the polyurethane stays flexible and handles vehicle traffic.
Can I just use sand instead of backer rod?
You can, but backer rod performs better. Sand lets sealant soak in unevenly and can trap moisture. Backer rod is inexpensive, sets an exact depth, and lets the sealant flex properly.
How deep should the sealant be in the joint?
The standard rule of thumb is a sealant depth of roughly half the joint width. In a 12 mm joint, aim for about 6 mm of sealant above the backer rod, finishing slightly below the slab surface.
When is the best time of year to seal driveway joints?
A mild, dry day in spring or autumn is best. Seal when the concrete is cool and contracted, so the joint is at its widest. Avoid hot afternoons, freezing weather, and any rain in the forecast.
How long do sealed expansion joints last?
A properly prepped and sealed joint typically lasts several years on a driveway, often five to ten, depending on traffic, sun exposure, and sealant quality. Joints sealed into dirty faces fail sooner.
Should expansion joints be filled before or after the concrete cures?
After. New concrete shrinks as it cures, and sealing too early means the joints open wider than the sealant can take. Wait at least 28 days on new slabs.
Conclusion
Filling expansion joints is a small job that pays off for years: backer rod to set the depth and break the bond, self-levelling polyurethane tooled just below the surface, and a mild dry day when the concrete is contracted. Respect the joints that should stay open, and keep traffic off until the sealant cures.
Last verified: October 2026.
About the author
Kaleemullah Formulas use standard geometry and published bag yields; sources are linked in each article.