Concrete Mix Ratio 1:2:4 Explained (Materials, Strength and UK Grades)

Concrete mix ratio 1 2 4 explained showing cement sand and aggregate parts by volume

A 1:2:4 concrete mix means 1 part cement, 2 parts sand and 4 parts coarse aggregate, measured by volume. To check the water-cement ratio of your own mix, use our water cement ratio calculator. It gives a medium-strength, general-purpose mix of about 15 N/mm2 at 28 days, suited to low-load domestic work like shed bases, paths and garden wall footings (not structural foundations). One cubic metre needs about 6.5 bags of 50 kg cement (317 kg), 0.44 m3 of sand and 0.88 m3 of aggregate.

UK readers will meet it described as the site-mixed equivalent for light domestic jobs, closer to GEN3 (C16/20) than to C20: a rule of thumb, not a certified grade.

Worked example: materials for 1 m3 of 1:2:4

The 1.54 dry-volume factor turns wet concrete into dry ingredients: 1 m3 of wet concrete needs 1.54 m3 of dry material, because the cement paste fills the air gaps between particles.

Step 1. Dry volume = 1 m3 x 1.54 = 1.54 m3.

Step 2. Split by the ratio (7 parts total). Cement = 1/7 x 1.54 = 0.22 m3. Sand = 2/7 x 1.54 = 0.44 m3. Aggregate = 4/7 x 1.54 = 0.88 m3.

Step 3. Convert cement to bags. At about 1,440 kg per m3 loose, 0.22 m3 is about 317 kg: about 6.5 x 50 kg bags, 13 x 25 kg (UK), or 7.5 x 94 lb (US).

Step 4. Work out the water. A water-cement ratio of 0.45 to 0.55 suits this mix: 0.45 to 0.55 kg of water per kg of cement, so 145 to 175 litres for 317 kg of cement, added gradually.

Material Metric UK (25 kg bags) US customary
Cement 317 kg (about 6.5 x 50 kg bags) About 13 x 25 kg bags About 7.5 x 94 lb bags
Sand 0.44 m3 0.44 m3 (bulk bag) About 15.5 ft3
Coarse aggregate 0.88 m3 0.88 m3 (bulk bag) About 31 ft3
Water 145 to 175 litres 32 to 39 gallons 38 to 46 gallons

Add 5 to 10% extra for waste. Our concrete mix ratio calculator does this for any volume and any ratio.

What the numbers mean

The three numbers are always cement, sand and coarse aggregate, in that order, by volume not weight. So 1:2:4 means one bucket of cement, two buckets of sand and four buckets of gravel, using the same bucket for all three. Volume is used because it is easy to measure on site; keep the container consistent and the mix stays reliable batch to batch.

1:2:4 compared with the other common ratios

Ratio Approximate 28-day strength Cement content Relative cost Best for
1:3:6 About 10 N/mm2 Lean, less cement Lowest Blinding, mass fill, non-structural work
1:2:4 About 15 N/mm2 Medium Moderate Paths, fence posts, shed bases (light duty only, not driveways)
1:2:3 About 15 to 20 N/mm2 Fairly rich Higher Patios and paths where extra strength helps
1:1.5:3 About 20 N/mm2 Rich, more cement Highest Reinforced columns, beams, structural work

Strengths are approximate because site batching varies. Use 1:3:6 to save on cement where strength does not matter, and 1:1.5:3 for structural work under engineer guidance.

The 1.54 dry-volume factor, explained simply

Dry ingredients contain air gaps that the cement paste fills when mixed, so the volume shrinks: multiply your target wet volume by 1.54, then split the dry volume by the ratio.

Materials per cubic yard for each ratio

These use the 1.54 factor and a 94 lb bag of cement (about 1 cubic foot). All values are approximate, so add 5 to 10% for waste.

Ratio Cement bags Sand Aggregate Water
1:3:6 about 4 12.5 ft3 25 ft3 about 25 gal
1:2:4 about 6 12 ft3 24 ft3 about 36 gal
1:1.5:3 about 7 to 8 11.3 ft3 22.7 ft3 about 45 gal

If you plan to use pre-mixed bags instead of raw ingredients, check the concrete bag calculator.

What each ingredient does

  • Cement is the glue. It reacts with water and hardens, binding everything together. More cement means stronger concrete and a higher price.
  • Sand fills the gaps between the stones. Use sharp sand, not soft building sand.
  • Coarse aggregate, usually gravel or crushed stone of about 20 mm, is the skeleton. It provides most of the strength and keeps costs down, because stone is cheaper than cement.
  • Water starts the hardening reaction. The amount matters enormously, as the next section explains.

Water: the ingredient people get wrong

Aim for a water-cement ratio of 0.45 to 0.55: less water gives stronger concrete, more gives weaker. Strength and workability pull in opposite directions, so this ratio is the real quality control on site.

Start with about 6 gallons of water per 94 lb bag of cement (about 23 litres, or 27 litres in UK gallons). Add it gradually and stop when the mix holds together without slumping into soup. Too much water is the classic mistake: it makes mixing easier but weakens the concrete and causes cracking as it dries.

The ballast shortcut (UK DIYers)

UK merchants sell ballast, sand and gravel already blended in roughly the right proportions. Mixing 1 part cement to 6 parts ballast approximates a 1:2:4 mix: 1 bucket of cement to 6 buckets of ballast, water added gradually. For larger pours, buy sand and gravel separately.

A small batch recipe you can use tomorrow

For a fence post or small repair, mix one batch at a time: 1 bucket of cement, 2 buckets of sharp sand, 4 buckets of coarse aggregate (or 6 buckets of ballast instead), and roughly half a bucket of water added gradually until workable. Mix the dry materials first, make a hollow, add half the water, then add the rest slowly. Place and finish within about 90 minutes of adding water.

A typical shed base (8 by 10 ft at 4 inches) needs about 1 cubic yard, which is many wheelbarrow batches, so a hired mixer keeps them consistent. Above one cubic yard, ready-mix usually wins.

Which ratio should you pick?

Job Suggested ratio Notes
Fence posts 1:2:4 Strong enough, sets at a handy speed
Garden path or patio slab 1:2:4 Add mesh or fibres for crack control
Footings for a wall or extension 1:2:4 Standard residential choice
Blinding under foundations 1:3:6 Lean mix, strength not critical
Shed base 1:2:4 or 1:3:6 Either works for light loads
Reinforced columns or beams 1:1.5:3 Follow the structural drawings
Driveway slab 1:2:4 Pour 6 in thick with rebar

These are starting points. Structural work should follow an engineer’s specification, not a table.

Pre-mixed bags vs mixing your own

Pre-mixed bags contain cement, sand and aggregate already blended; you just add water. They suit small jobs: fence posts, small pads and repairs. An 80 lb bag yields 0.60 ft3, and 45 bags make one cubic yard. Mixing your own suits bigger jobs, where bulk materials cost less per yard. The break-even point sits around one cubic yard.

FAQs

What is a 1:2:4 mix of concrete?

It means 1 part cement, 2 parts sand and 4 parts coarse aggregate by volume, using the same container for each part. The standard general-purpose mix for footings, slabs, paths and fence posts.

How many bags of cement do I need for 1 m3 of 1:2:4 concrete?

About 6.5 bags of 50 kg cement (about 317 kg): about 13 x 25 kg bags in the UK, or about 7.5 x 94 lb bags in the US. Add 0.44 m3 of sand, 0.88 m3 of aggregate, 145 to 175 litres of water, and 5 to 10% for waste.

What is the water-cement ratio for a 1:2:4 mix?

Aim for 0.45 to 0.55 kg of water per kg of cement, about 6 gallons per 94 lb bag. Add it gradually and judge by texture. Less water gives stronger concrete, so resist the urge to flood the mix.

What is the strongest concrete mix ratio?

Of the common site ratios, 1:1.5:3 is the strongest at about 20 N/mm2 at 28 days. It suits reinforced columns, beams and structural work under an engineer’s specification.

Can I measure the mix with a shovel instead of buckets?

You can, but buckets are more consistent. Shovel loads vary with each scoop, which changes the ratio batch to batch. For fence posts a shovel count is fine; for slabs, use a bucket.

Is a 1:2:4 mix the same as C20 concrete?

Not exactly. C20 is a certified grade with tested strength, while 1:2:4 is a site-batched recipe. UK merchants treat 1:2:4 as the practical equivalent for the same domestic, non-structural jobs. If the specification calls for certified C20, order it from a batch plant.

Conclusion

Remember the order: cement, sand, aggregate. For most jobs, 1:2:4 mixed by volume does the work. Respect the 1.54 factor, keep the water-cement ratio between 0.45 and 0.55, and give the concrete 7 days of moist curing to reach its strength.

Related guides: Once poured, follow our guide on how to cure concrete. See our concrete drying and curing times for when you can load the slab.

About the author

Kaleemullah Formulas use standard geometry and published bag yields; sources are linked in each article.

Leave a Comment

Your email address will not be published. Required fields are marked *

Scroll to Top