Concrete PSI Chart: US PSI to UK Strength Grades (C20/25, C28/35, GEN Mixes)

Concrete test cubes being crushed in a hydraulic testing machine inside a construction materials laboratory

Concrete PSI Chart: US PSI to UK Strength Grades

Watch enough American building videos and you will hit the same wall: they talk about 3000 or 4000 PSI concrete, while British suppliers talk about C20/25, C28/35, or GEN3. They are two languages for the same thing, and this chart translates between them.

Direct answer: Concrete PSI (pounds per square inch) is the American measure of compressive strength, while the UK uses MPa and C-grades such as C20/25. To convert, divide PSI by 145 to get MPa. As an approximate guide, 2500 PSI is close to C16/20, 3000 PSI is close to C20/25, 4000 PSI is close to C28/35, and 5000 PSI is close to C35/45. Use the chart below for the full mapping.

The Unified Concrete PSI Chart

Every conversion in this table is approximate, because the two systems test concrete differently. The US mostly tests cylinders, while the UK C-grade records both a cylinder value and a cube value (hence C20/25, which means 20 MPa on a cylinder and 25 MPa on a cube). Treat the mappings as practical equivalents for buying and specifying concrete, not as lab-exact identities.

US strength (PSI) MPa (approx) UK C-grade (approx) UK designated mix Typical nominal ratio (approx) Common uses
2000 14 C12/15 GEN1 1:3:6 Blinding, kerb bedding, mass fill
2500 17 C16/20 GEN3 1:2:4 Patios, footpaths, unreinforced bases
3000 21 C20/25 GEN3 / RC25/30 1:2:4 Domestic driveways, garage floors, footings
4000 28 C28/35 RC28/35 1:1.5:3 Reinforced driveways, shed slabs, farm paving
5000 35 C35/45 RC40/50 1:1:2 Commercial slabs, structural beams

A few notes on the table. First, 1 MPa equals roughly 145 PSI, so 3000 divided by 145 gives about 20.7 MPa, just above the C20/25 cylinder value. Second, the nominal ratios are rough volume guides for site-batched work; ready-mix plants design their own mixes. Third, GEN and RC are BS 8500 designated mixes, which guarantee minimum strength plus durability for the intended use.

How Cylinder and Cube Testing Differ

In the United States, a 150 by 300 mm cylinder is crushed in a press, and the result in PSI becomes the stated strength. In the UK, both cylinders and 100 or 150 mm cubes are used, and the grade carries both numbers. That is why a C20/25 grade means the concrete reached at least 20 MPa in a cylinder test and 25 MPa in a cube test. Cubes read higher than cylinders for the same concrete because of how the shape resists the press, which is why the second number is always bigger. When an American says 4000 PSI and a Brit says C28/35, they are describing concrete that fails at nearly the same load.

UK GEN and RC Mixes Explained

Designated mixes are the UK shortcut for ordering. Instead of specifying every ingredient, you name the designation and the plant supplies a mix that meets the standard. The common ones for domestic and light commercial work are:

  • GEN0: Unreinforced domestic foundations and kerb bedding in non-aggressive soil. Roughly equivalent to C8/10.
  • GEN1: Blinding concrete and mass foundations where no reinforcement is used. Roughly C10/15 territory.
  • GEN3: Trench fill, strip foundations, and general domestic groundwork. Sits around C16/20 to C20/25.
  • RC25/30: Plain (unreinforced) domestic paving with light vehicle traffic.
  • RC28/35: Paving that is reinforced or contains fibres, agricultural yards, and domestic driveways that take heavier loads.
  • RC32/40 and RC40/50: Heavy duty industrial paving and structural work.

If a US guide tells you to pour 4000 PSI for a driveway and your local plant sells RC28/35, you are ordering the right thing. If it says 3000 PSI for a patio, ask for GEN3 or a C20/25 equivalent and you will match it.

What to Tell the Ready-Mix Plant

Strength is only one part of an order. When you phone the plant, give them this information and they will sort the rest:

  • Strength class or designation: for example C28/35, GEN3, or RC28/35.
  • Exposure class: XC for general reinforced work, XF if the concrete faces frost and de-icing salts. The plant needs this to pick the right cement content.
  • Maximum aggregate size: 20 mm is standard for slabs, paths, and foundations.
  • Consistency (slump) class: S3, which is about 75 to 100 mm of slump, suits most hand-placed slabs. Order a wetter mix only if you are pumping.
  • Fibre or reinforcement: mention if you want steel or synthetic fibres added at the plant, which saves labour on site.
  • Volume: use a concrete cost calculator to work out your cubic metres before you call, so you order the right load plus a small allowance for waste.

Ordering by designation rather than by raw PSI keeps everything in the UK system the plant actually works with, and it gives you the durability guarantees that a bare strength number does not.

Pressure Washer PSI Is a Different Thing Entirely

One quick clarification, because the bare phrase “concrete PSI” sends plenty of people to pressure washer pages. A pressure washer rated at 3000 PSI is describing the pressure of the water jet at the nozzle, measured in pounds per square inch. Concrete strength PSI is describing the crushing load a cured sample can take, measured the same units but in a completely different context. A 3000 PSI pressure washer does not produce “concrete strength” water, and 3000 PSI concrete does not need a 3000 PSI washer to clean it. If you arrived here looking for washer guidance, the short version is this: 2000 to 3000 PSI washers handle domestic patios and driveways fine, and you should keep the nozzle moving so you do not etch the surface.

Typical Strengths for Common DIY Jobs

If you just want the buying answer for a project, here is the short list:

  • Garden path or patio slabs: 2500 PSI equivalent, C16/20 or GEN3. No reinforcement needed for foot traffic.
  • Domestic driveway: 3000 PSI equivalent, C20/25. Add mesh or fibres if cars will park on it daily.
  • Garage floor: 3000 to 4000 PSI equivalent, C20/25 to C28/35. Reinforcement is wise because of point loads from jacks.
  • Shed base: 2500 PSI equivalent, C16/20. Keep it simple and level.
  • House extension footings: follow the structural engineer’s specification, but GEN3 or C20/25 is the common domestic default.
  • Fence post concrete: 2500 PSI equivalent is plenty; post holes are about stability, not crushing strength.

When you mix on site rather than ordering ready-mix, check your ratios with a concrete mix ratio calculator and always round your bag count up. Running short mid-pour is far more expensive than one spare bag.

FAQ

What is the UK equivalent of 3000 PSI concrete?
About C20/25, which is 20 MPa on a cylinder test. In BS 8500 terms you would order GEN3 for general groundwork or RC25/30 for plain paving.

What is the UK equivalent of 4000 PSI concrete?
About C28/35, which is 28 MPa on a cylinder test. The matching designated mix is RC28/35, the standard choice for reinforced domestic driveways and farm paving.

How do I convert PSI to MPa?
Divide the PSI number by 145. So 3000 PSI divided by 145 gives about 20.7 MPa. This is approximate but close enough for specifying and buying.

What does C20/25 actually mean?
It means the concrete achieved at least 20 MPa in a cylinder crush test and 25 MPa in a cube crush test at 28 days. The two numbers come from the two standard UK test specimen shapes.

What is the difference between GEN3 and C20/25?
C20/25 is a strength class: a pure strength statement. GEN3 is a designated mix under BS 8500 that guarantees a minimum strength around that level plus durability requirements for its intended uses, such as foundations and trench fill.

Can I use 2500 PSI concrete for a driveway?
It is light for one. 2500 PSI (about C16/20) suits patios and paths, but a driveway that carries cars daily is better at 3000 PSI (C20/25) with mesh or fibre reinforcement to control cracking.

UK grades: cylinder vs cube strength

UK grade Cylinder strength Cube strength Approx PSI (cube)
C12/15 12 MPa 15 MPa 2,175
C20/25 20 MPa 25 MPa 3,625
C25/30 25 MPa 30 MPa 4,350
C28/35 28 MPa 35 MPa 5,075
C32/40 32 MPa 40 MPa 5,800

The two numbers in a UK grade are the cylinder and cube strengths in MPa. PSI figures use 1 MPa = 145 psi, rounded.

Conclusion

PSI and C-grades are simply two dialects of the same measurement. Divide PSI by 145 to get MPa, match the result to the nearest C-grade in the chart, and order by the UK designation your plant recognises. Get that translation right and you will never again stand on site wondering whether the American video you watched and the British concrete you ordered are actually the same material.


Sources

About the author

Kaleemullah Formulas use standard geometry and published bag yields; sources are linked in each article.

Leave a Comment

Your email address will not be published. Required fields are marked *

Scroll to Top