
Epoxy injection repairs narrow, stable cracks in poured concrete by filling the full depth of the crack with a two-part epoxy that cures harder than the concrete around it. It is the standard DIY and professional method for cracked basement walls, foundations, and slabs where the crack is not still moving. A typical 8-foot wall crack takes an afternoon to inject and 24 to 48 hours to cure before you remove the ports.
When epoxy injection is the right fix
Epoxy injection suits cracks in poured concrete (walls, foundations, slabs) that are narrow, typically from hairline up to about 6 mm wide, and no longer moving. The classic case is a vertical shrinkage crack in a basement wall that leaks in heavy rain. Injected epoxy fills the crack through its full depth, bonds the two faces, and stops the leak permanently.
Before you buy a kit, every item on this checklist must be true:
- The cause is fixed. Settlement, drainage, or loading issues must be addressed first, or the failure just moves next door.
- The crack is not active. Epoxy cures rigid, so it cannot stretch with a crack that still opens and closes. For moving cracks, use flexible polyurethane.
- The concrete is sound. It must be solid, not crumbling. Epoxy cannot bond to dust.
- The surface is dry. Standard surface sealers need dry concrete to grip. Dry the area with a heat gun if damp.
If any of these fail, epoxy is the wrong product. Most kit-selling pages skip this checklist, and it is the reason many DIY epoxy repairs fail.
When NOT to use epoxy
Epoxy is not a universal crack filler. Do not use it for:
- Wide or structural cracks. Cracks wider than about 6 mm, horizontal foundation cracks, or cracks with vertical displacement can signal structural movement. Get a specialist to look first. Our DIY concrete mistakes guide explains which warning signs mean “call a professional”.
- Cracks that are still moving. Rigid epoxy will crack again. Use a flexible sealant or polyurethane injection.
- Concrete block walls. Hollow cores and mortar joints do not inject cleanly.
- Spalled or crumbling concrete. Remove and replace the bad concrete first; epoxy cannot bond to dust.
What is in an epoxy crack repair kit
A standard low-pressure DIY kit contains everything except basic tools:
| Component | What it is | What it does |
|---|---|---|
| Injection epoxy (2-part) | Low-viscosity resin plus hardener | Flows deep into the crack and cures into a rigid, structural fill |
| Surface seal paste (2-part) | Thick epoxy paste | Seals the crack face so injection pressure stays inside the crack |
| Injection ports | Small plastic nozzles with a base flange | Entry points for the epoxy, spaced along the crack |
| Applicator | Dual cartridge gun or syringe | Mixes and dispenses the two parts in the right ratio |
| Mixing supplies | Sticks, paddle, sometimes a drill mixer | For the surface seal paste, which is hand-mixed |
| PPE | Nitrile gloves, sometimes glasses | Skin and eye protection (uncured epoxy is a sensitiser) |
Most DIY kits cover about 8 to 10 feet of crack. Measure your crack and buy the right kit size.
Step-by-step: injecting a wall crack
Work in a ventilated area, wear nitrile gloves and eye protection, and read your kit’s instructions first. Formulations differ.
Step 1: Prepare the surface. Lay a dust sheet. Scrub the crack with a wire brush to remove loose material, dirt, paint, and efflorescence, about 25 to 50 mm on each side. Blow out dust. The surface must be dry.
Step 2: Mark port positions. Start about 100 mm above the bottom of the crack. Mark every 200 mm along its length. Ports spaced 150 to 300 mm apart is the normal range.
Step 3: Mix the surface seal paste. Mix only as much as you can spread in 2 to 3 minutes. Combine the two parts and stir about 30 seconds until the colour is uniform.
Step 4: Attach the ports. Butter each port’s base flange with paste without blocking the nozzle opening. Press onto the wall centred over the crack at your marks, add more paste around the base, and let set about 10 minutes.
Step 5: Seal the crack face. Trowel paste over the entire crack between ports, about 3 mm thick and 25 mm to each side. Do not push paste into the crack; you are building a pressure lid.
Step 6: Inject from the bottom up. Once the seal is tack-free, start at the lowest port. Inject slowly until epoxy oozes from the next port up. Plug the first port, move up one, and repeat until every port is filled.
Step 7: Cure and finish. Leave alone 24 to 48 hours. Knock ports off with a hammer, grind the seal flush, and paint once fully cured.
How long epoxy takes to cure
Cure time depends on product, temperature, and humidity. Warmer conditions speed curing; cold and damp slow it:
| Stage | Typical time | What it means |
|---|---|---|
| Working (pot) life | 15-40 minutes after mixing | How long you have to inject before the mix thickens |
| Gel | 20-30 minutes | Epoxy turns semi-rigid; do not disturb ports |
| Tack-free / hard | A few hours | Surface seal can be touched; ports stay put |
| Port removal | 24-48 hours | Safe to knock off ports and finish the surface |
| Full strength | About 7 days | Maximum compressive and tensile strength reached |
Do not load or stress the repair until the full cure period on your kit’s label has passed. If you are timing other work around the repair, our concrete drying and curing times guide covers how concrete gains strength.
Epoxy vs polyurethane vs cement patch
Choosing the wrong filler is the most expensive mistake in crack repair. Here is the honest comparison:
| Method | Best for | Strength | Flexibility | DIY difficulty |
|---|---|---|---|---|
| Epoxy injection | Stable, narrow cracks in poured concrete; structural rebonding | Highest; cured epoxy typically exceeds the concrete’s own compressive and tensile strength | Rigid; none | Moderate; ports and patience required |
| Polyurethane injection | Leaking cracks, including slightly active ones; wet conditions | Good; bonds well but not a structural rebond | Flexible; tolerates minor movement | Moderate; similar port method |
| Cement/polymer patch | Surface spalls, shallow defects, cosmetic cracks | Matches the patch material, not the original | Rigid; none | Easy; trowel on |
Rule of thumb: if the crack is stable and you want the wall to act as one piece again, use epoxy. If it leaks and may still move slightly, use polyurethane. If the damage is only skin-deep, a polymer-modified patch is faster and cheaper.
Common mistakes with epoxy crack repair
- Skipping the stability check. Injecting a crack that is still moving guarantees a callback. Monitor the crack across a season if you are unsure.
- Mixing too much at once. Epoxy has a short pot life. Mix small batches, especially the surface paste.
- Starting at the top. Always start at the lowest port so epoxy rises through the crack and pushes air out ahead of it.
- No PPE. Uncured epoxy can sensitise skin with repeated exposure. Nitrile gloves every time, plus eye protection and ventilation.
Frequently asked questions
How much does epoxy crack injection cost?
A DIY kit for an 8 to 10 foot crack costs far less than a professional visit, which is why most homeowners do it themselves. Professional injection is priced per crack or per linear foot and varies by region.
Is epoxy stronger than concrete?
Manufacturers and structural repair firms report that cured injection epoxy typically exceeds the compressive and tensile strength of the surrounding concrete. That is why it is used for structural rebonding: the repaired section is not the weak point.
Can I inject a crack that is leaking water?
Not with standard epoxy. The surface must be dry for the seal paste to cure. Either wait for dry conditions and dry the crack with a heat gun, or use a polyurethane foam that is designed to cure in the presence of water.
How wide a crack can epoxy fill?
Low-viscosity injection epoxies handle hairline cracks up to about 6 mm. Wider cracks need a different approach: a thicker epoxy paste, or routing and sealing, or professional assessment if structural.
Will the crack come back?
If the crack was stable and the cause is fixed, a proper epoxy injection is permanent. If it reopens beside the repair, the underlying movement was never addressed.
Can I paint over the repair?
Yes, once fully cured. Grind the surface seal flush first, then prime and paint as normal.
Conclusion
Epoxy injection is the right tool for stable, narrow cracks in poured concrete: it fills the full depth, cures stronger than the concrete itself, and stops leaks permanently. Its limits matter just as much: it cannot fix moving cracks, structural failures, or unsound concrete, and it needs dry conditions. Check the prerequisites, inject slowly from the bottom up, respect the cure times, and wear your PPE. Thin slabs crack for preventable reasons too; our slab thickness guide shows how the right depth stops most slab cracks before they start.
Last verified: October 2026.
About the author
Kaleemullah Formulas use standard geometry and published bag yields; sources are linked in each article.