Concrete pavers turn a plain patio or tired driveway into a surface that looks sharp, drains well and can be repaired one unit at a time. The pavers are the easy part. The layers underneath decide whether the surface stays flat for years or starts to sink and spread.
Direct answer: To install concrete pavers, mark out the area, set a fall away from buildings, dig to paver thickness plus about 1 inch of bedding sand plus the compacted base, compact the base in lifts, screed a 1 inch sand bed, lay pavers from a straight edge, fit edge restraint, then sweep joint sand in and compact. For a patio, plan on at least 4 inches of compacted base. For a residential driveway, plan on at least 6 inches.
Before you dig: plan the layout and the fall
Start with a sketch. Measure length and width, note fixed edges such as a house wall or step, and decide where water should go. Water must run away from buildings and door thresholds. A fall of about 2 percent, roughly 1/4 inch per foot, is a common residential target. On a 10 foot patio, the far edge sits about 2.5 inches lower than the edge at the house.
Set stakes outside the work area and run taut string lines at the planned finished height. Check them with a level. Mark the area with spray paint, then call your local utility locating service before you dig.
Materials and tools you will need
A paver job needs more than pavers. Gather base material, bedding sand, joint sand and edge restraint before you dig, so the base is not left open to rain. Dense graded crushed stone is the usual base material. Bedding sand should be clean concrete sand that meets ASTM C33. Do not use stone dust or mason sand as bedding sand.
- Pavers, plus about 5 percent extra for cuts and breakage
- Crushed stone base material, compacted in lifts
- ASTM C33 concrete sand for bedding, and joint sand or polymeric sand for joints
- Edge restraint and spikes, suited to the paver system you bought
- Geotextile fabric, useful on clay or weak soil to stop base stone sinking into mud
- Stakes, string line, tape measure, level, rake, shovel and wheelbarrow
- Plate compactor, screed rails and a straight screed board
- Masonry saw or paver splitter, rubber mallet, broom and safety glasses, gloves and hearing protection
Step 1: Excavate to the right depth
Excavation depth is a calculation, not a guess. Add paver thickness, about 1 inch of bedding sand and the compacted base depth. A 60 mm patio paver is about 2 and 3/8 inches thick. On a 4 inch base, the dig is about 7.5 inches. A driveway with an 80 mm paver and a 6 inch base digs deeper, about 10 inches. Remove all topsoil, roots and soft or unstable material. Topsoil compresses and rots, so it must not stay under a base.
Compact the exposed subgrade. If soil is soft or clay heavy, lay geotextile fabric over it before base stone goes in. It stops stone pressing into mud. Keep excavation slightly wider than the paver field so edge restraint sits on compacted base.
Step 2: Build the base in thin lifts
Spread base stone in lifts of about 2 to 3 inches, dampen lightly if dry, then compact each lift fully before adding the next. Thick loose layers do not compact evenly. The finished base should feel hard underfoot.
Check the base level often with string lines. Bedding sand cannot fix a low base. If you find a dip, add base stone and compact again.
| Use | Compacted base minimum | Paver thickness often used | Notes |
|---|---|---|---|
| Patio or walkway | 4 inches | 60 mm | Add depth on weak soil or in deep frost areas |
| Residential driveway | 6 inches | 80 mm | Use a thicker paver for vehicle loads |
| Heavy vehicles or commercial use | 8 to 12 inches | 80 mm or thicker | Get engineering advice for heavy loads |
Step 3: Screed the bedding sand
Set screed rails on the compacted base, spread bedding sand between them and pull a straight board across in one smooth pass. The result should be about 1 inch thick. Do not compact bedding sand before laying pavers, and do not walk on it. Screed only as much area as you can lay at once.
Step 4: Lay the pavers in pattern
Start from a long straight fixed edge or square layout line. A house wall makes a good reference if it is straight. Lay pavers lightly onto the sand. Do not press or hammer them into the bed. Keep joints even and check alignment with a string line every few rows.
Work forward from the laid surface, not from the sand. Standing on sand leaves footprints that become dips. Set a herringbone angle carefully at the start, as a small error grows across a large field, and shift the field slightly if that avoids a thin cut at an edge.
Step 5: Fit edge restraint, joint and compact
Edge restraint is not optional. Without it, pavers creep outward and joints open up. Plastic or metal restraint is spiked into compacted base along open edges. A kerb or wall can act as restraint where it is tight to the field.
Spread dry joint sand over the surface and sweep it into the joints. Run the plate compactor over the pavers with a protective pad, then sweep in more sand and compact again. Polymeric sand needs a dry surface and a light watering step, so follow the label exactly.
Finishing, sealing and maintenance
Backfill edges with topsoil, keeping soil below paver level so water can drain off. Sealing is optional. It can deepen colour, slow staining and help hold joint sand. Wait until the surface is clean and dry, and follow the label for coats and drying time.
Maintenance is light. Sweep regularly, top up joint sand when it drops, and pull weeds early. If a paver sinks, lift it, correct the base beneath it, and relay it. See our concrete slab thickness guide and concrete patio thickness guide for related projects.
| Problem | Likely cause | Fix |
|---|---|---|
| Sinking in one area | Thin or poorly compacted base, or soft subgrade | Lift pavers, rebuild base in lifts, relay |
| Rocking pavers | Uneven bedding sand or a high spot | Lift unit, re-screed sand locally, relay |
| Spreading edges | Missing or loose edge restraint | Refit restraint spiked into compacted base |
| Weeds in joints | Open or low joint sand | Top up joint sand, consider polymeric sand |
Common mistakes to avoid
- Digging to a fixed depth instead of calculating paver plus sand plus base.
- Using bedding sand to level a poor base.
- Skipping edge restraint on open sides.
- Compacting bedding sand before laying pavers.
- Laying pavers while standing on the screeded sand.
- Using stone dust as bedding sand.
- Sealing before the surface and joints are clean and dry.
When to hire a professional
A small patio on firm soil is a realistic DIY job with a rented compactor. Hire a professional for large driveways, heavy vehicle areas, drainage changes near a foundation, or sites with poor soil or a high water table.
Frequently asked questions
How deep should I dig for concrete pavers?
Add paver thickness, about 1 inch of bedding sand and the compacted base depth. For a 60 mm patio paver on a 4 inch base, that is about 7.5 inches.
Can I lay pavers on soil or on grass?
No. Soil moves and compresses unevenly. Pavers need a compacted stone base, a screeded sand bed and edge restraint.
What sand do I use under pavers?
Use clean concrete sand that meets ASTM C33, screeded to about 1 inch. Do not use stone dust or mason sand as bedding sand. Joint sand can be plain or polymeric sand.
Do I need edge restraint for pavers?
Yes, on every open edge. A wall or kerb can act as restraint where tight to the field. On open sides, use restraint spiked into compacted base.
How long before I can use a new paver patio?
You can usually walk on a finished patio at once. Wait for polymeric sand and sealer to cure as directed before heavy use. Driveways should not take vehicles until jointing is complete.
Can I replace a single damaged paver?
Yes. Lift the damaged unit, correct any dip beneath it, set a matching paver and refill the joints.
Conclusion
Good paver work is mostly hidden work. Plan the fall, dig to a calculated depth, compact the base in thin lifts, screed one even inch of sand, lay from a straight edge and lock the field with restraint and full joints. Rush the base and no pattern or sealer will save the job.
Sources
- Crafting With Concrete: How to Install Concrete Pavers in 5 Steps
- This Old House: How To Install Concrete Pavers
- RCP Block: Concrete Interlocking Paver Installation
- CalcSummit: Paver Calculator, Quantity, Base and Cost
- Anvilfield: Paver and Hardscape Installation Field Guide
About the author
Kaleemullah Formulas use standard geometry and published bag yields; sources are linked in each article.