How to Build a Concrete Retaining Wall

New concrete block retaining wall with gravel drainage and cap units in a garden.

A concrete retaining wall holds back soil so you can level a garden, build a terrace or stop a slope from sliding. It is a simple idea with serious forces behind it. Soil gets heavy when wet, and water trapped behind a wall can push it over. This guide shows how to build a small garden retaining wall safely, and when to stop and call an engineer.

The direct answer

To build a small concrete retaining wall, check local rules first, mark the line, dig a level trench, build a compacted gravel base or a concrete footing, lay blocks in a running bond with a slight setback, add gravel and a drain pipe behind the wall, backfill in thin layers, and cap the top. Keep DIY walls low. In many areas, walls over about 1.2 metres, walls that support a drive or a building, and walls on steep or poor ground need a permit and an engineered design.

First decide if this is a DIY job

Height is the first test. A wall under about 900 mm on flat, firm ground is a realistic DIY project. A wall over 1.2 metres carries far more soil pressure and often needs engineering. Surcharge is the second test. If a drive, patio, building or steep slope sits above the wall, get professional advice even if the wall looks low.

Soil and water are the third test. Clay holds water and swells, and loose fill settles. If you are unsure about any test, ask a local engineer before you buy blocks. A failed wall is costly and dangerous.

Choose the wall type

Interlocking segmental blocks are the easiest for DIY. They stack with a lip or pin, step back into the slope by design, and many need no mortar. Standard concrete blocks need mortar and reinforcement. Poured concrete needs formwork and steel. For a first wall, interlocking blocks are usually best.

Wall typeBest forWatch out for
Interlocking blocksLow garden walls, curvesFollow the maker limits on height
Mortared concrete blocksStraight walls, rendered finishNeeds mortar skill and steel
Poured concreteStraight walls, heavy loadsFormwork and steel design matter

Tools and materials

You need digging tools, a level, a string line, a rubber mallet and a compactor. Order blocks, caps, gravel, drain pipe and filter fabric before you dig.

ItemWhat it is for
Blocks and cap unitsWall face and finished top
Crushed stone baseLevel, draining footing layer
Clean drainage gravelWater path behind the wall
Perforated drain pipeCarries water to a safe outlet
Filter fabricStops soil washing into gravel
Level, string and malletKeeping courses level and true

Plan drainage before you stack

Water is the main cause of retaining wall failure. Rain soaks the soil behind the wall, and that wet soil pushes hard. Plan a zone of clean gravel at least 300 mm wide behind the wall, from base to near top. Place a perforated pipe at the base of that gravel, holes facing down, sloped to a safe outlet.

Filter fabric sits between soil and gravel. It lets water through but stops fine soil clogging the gravel. Weep holes do not replace a drain pipe and gravel. For footing sizes, see our guide to calculating concrete for footings.

Step by step: build a small block wall

1. Check services and set out

Call your local utility location service before digging. Mark the wall face with paint or a hose. Set string lines at the finished height. Check the line from both ends and from the house. A wall that looks right from one side can drift badly over a long run.

2. Dig the trench

Dig a trench wide enough for the base plus working room, and deep enough for the base gravel plus one buried block course. Many block makers call for at least one full buried course, and more on a slope. Keep the trench bottom level. Step the base on a slope instead of following the slope with a leaning wall.

3. Build the base

Spread crushed stone in layers about 50 to 75 mm thick. Compact each layer. A common base for a small wall is about 150 mm of compacted stone, but follow your block maker guide for your height and soil. Check the base with a level in both directions. The first course sets the whole wall. If it is out of level, every course above it will be too.

4. Lay the first course

Place the first blocks on a thin levelling layer. Tap each block level with a rubber mallet. This course takes the longest time, and that time is well spent.

5. Stack, set back and fill

Stack the next courses in a running bond, so joints do not line up. Keep the maker setback, often about 20 mm per course, so the wall leans slightly into the slope. Place drainage gravel behind each course as you rise.

6. Lay the drain and backfill in layers

Place the perforated pipe near the base, inside the gravel zone, and wrap it in fabric if your guide calls for it. Backfill with gravel behind the wall and soil further back, in layers about 150 mm thick. Compact each layer lightly. Do not use heavy plant right behind a new wall. It can push the wall forward before the structure is complete.

7. Cap and finish

Brush the top course clean. Glue or mortar cap units in place as the maker directs. Finish the top soil with a slight fall away from the wall, so surface water does not pond behind it. Seed or plant only after the wall is complete and the backfill has settled a little.

Mistakes that cause failure

  • No drain pipe and no gravel behind the wall.
  • A base that was never compacted, so the wall settles unevenly.
  • Backfilling with clay right against the wall face.
  • Building too high for a DIY block system.
  • Letting the drain outlet discharge onto a neighbour or a path.
  • Stacking joints in line instead of in a running bond.

When you must get professional help

Get an engineer for walls over the local permit height, walls with a surcharge above, walls near a boundary or a building, walls on fill or soft soil, and tiered walls where the total retained height is high. Also get advice if the wall shows signs of movement, such as leaning, bulging, cracking or a drain that runs dirty with soil. Early advice is far cheaper than a rebuild. For reinforcement choices on slabs, see our rebar versus wire mesh guide.

Aftercare and warning signs

Check the wall after heavy rain for leaning, cracks, bulging and ponding. Clear the drain outlet. Small movement is a warning, not a cosmetic fault. Get advice if it moves again.

Frequently asked questions

How high can I build a retaining wall myself?

Many DIY guides treat walls under about 900 mm as suitable for a careful home builder, and walls over about 1.2 metres as needing checks. Always check your local rules, because limits vary by area.

Do I need drainage behind a small wall?

Yes. Even a low wall needs gravel and a drain outlet. Water pressure builds behind any wall that holds wet soil, and drainage is what keeps that pressure low.

What is the best base for a block retaining wall?

A compacted crushed stone base, laid in thin layers and checked level, suits most small segmental walls. A mortared wall may need a poured concrete footing instead.

Can I build a retaining wall on a slope?

Yes, but step the base and keep each section level. Do not build one long leaning wall that follows the slope. Tiered walls need extra care with total height.

How do I stop a retaining wall leaning?

Use the maker setback, compact the base, drain water away, backfill in thin layers and do not overload the top. A leaning wall needs professional advice, not more backfill.

Do I need a permit for a garden retaining wall?

It depends on height, surcharge and local rules. Many areas require a permit over about 1.2 metres of retained height. Check with your local building department before you dig.

Conclusion

A retaining wall succeeds when the base is level, the courses are true and water has a clear way out. Build low, drain well, backfill in layers and respect height limits. If the wall is tall, loaded or on tricky ground, an engineered design is not an extra cost. It is the job itself.

Sources

About the author

Kaleemullah Formulas use standard geometry and published bag yields; sources are linked in each article.

Leave a Comment

Your email address will not be published. Required fields are marked *

Scroll to Top